CIRCULÉIRE NON-MEMBER CASE STUDY
COMPANY: SATAIR
WEBSITE: SATAIR.COM
SECTOR: AVIATION INDUSTRY
PUBLISHED: 20th NOVEMBER 2026
TAGS: CIRCULAR MANUFACTURING, REPAIR, REUSE, ADDITIVE MANUFACTURING, 3D PRINTING, SPARE PARTS, PRODUCT LIFETIME EXTENSION, CRITICAL RAW MATERIALS, RESOURCE EFFICIENCY, SUPPLY CHAIN RESILIENCE

The Challenge
Commercial aircraft stay in service for decades. Passenger aircraft are typically retired after 25 to 30 years and freighters after 30 to 40 years (EASA, 2024). The average age of aircraft in the European fleet continues to rise and stood at 11.8 years in 2023. The European Union Aviation Safety Agency (EASA) reports that supply chain problems are delaying the replacement of older aircraft with new ones (EASA, 2025a).
Once an aircraft model goes out of production, replacement parts can become hard to source, especially if the original supplier stops trading or no longer holds the tooling (Mohd Yusuf, Cutler and Gao, 2019). The International Air Transport Association (IATA) estimates that supply chain problems could cost airlines more than US$11 billion in 2025. Because deliveries of new aircraft are delayed, airlines are flying older, less fuel-efficient aircraft, which adds about US$4.2 billion in fuel costs. Older aircraft also need more frequent and expensive maintenance, which adds US$3.1 billion. Airlines are stocking more spare parts to guard against unpredictable disruptions, which adds US$1.4 billion in inventory costs (IATA, 2025). In aviation, making unique spare parts in large batches carries a high risk that they become obsolete (Mohd Yusuf, Cutler and Gao, 2019). Across manufacturing more widely, an EU-funded project noted that warehouses of spare parts kept for needs that may never arise, lead to high costs and large amounts of scrap (European Commission, 2012).
Most attention on aviation’s environmental impact goes to the flying stage, which EASA describes as the stage with the greatest impact, mainly from greenhouse gases and noise (EASA, 2024). Aviation produced approximately 2.5% of global CO₂ emissions in 2023, and its emissions in absolute terms have grown significantly (EASA, 2025b). However, EASA points out that the production and end-of-life stages of an aircraft also affect the environment, so they too can be improved (EASA, 2024).
A Circular Solution
Satair is a stand-alone Airbus subsidiary that supplies parts, tools and services to the commercial aviation aftermarket, the market that keeps aircraft maintained once they are in service. The company was founded in 1957 to trade surplus parts from retired aircraft (Satair, 2026a). Satair says it aims to safeguard parts rather than scrap them and buy new ones. According to the company, keeping parts in service for longer is about more than sustainability, because repair and reuse also give airlines another source of parts and make their operations more resilient (Satair, 2026b).
In circular economy terminology, repair is “repair and maintenance of a defective product so it can be used with its original function” (Potting et al., 2017). According to Satair, repair is often the first choice on older aircraft programmes, such as the Airbus A380 and earlier versions of the A320 and A330, because a reliable supply of new parts is not always available. The company routes parts through a network of more than 25 repair stations, including facilities owned by Airbus, matching each part to a suitable repair specialist (Satair, 2026b). Satair also works with Airbus engineers to make more parts repairable. For example, when lightning damaged a sharklet (the upturned wingtip on some Airbus aircraft), some of its panels previously had to be replaced. New repair methods now allow more of these panels to be kept rather than replaced (Satair, 2026b).
In circular economy terminology, reuse is “re-use by another consumer of a discarded product which is still in good condition and fulfils its original function” (Potting et al., 2017). In aviation, parts that still work can be taken from retired aircraft and reused as spares on other aircraft, but this depends on the parts’ records being available (EASA, 2024). Satair calls these parts used serviceable material (USM). The company expanded into USM by buying VAS Aero Services in 2022, and Unical Aviation and its subsidiary ecube, which dismantles aircraft, in 2026 (Satair, 2026a). To decide which parts to take from aircraft being dismantled, Satair can draw on a “harvesting list” of the parts airlines need. Those parts can then be repaired and returned to stock, so airlines do not have to wait for scarce parts to appear on the market. Before a used part can be sold or exchanged, Satair’s airworthiness assessors review its records (Satair, 2026b).
In 2020, Satair turned to 3D printing, also known as additive manufacturing, when a US airline customer needed wingtip fences for its Airbus A320ceo aircraft, part of a family of more than 7,000 aircraft in service at the time. The original supplier had difficulty providing the cast part, which led to moulds regularly being lost and a potentially high cost for Satair to replace them for individual orders. Redesigning the part to be machined was not competitive on cost or lead time (Airbus, 2020). Airbus’s RapidSpares design office re-certified the former cast part within five weeks and adapted it to be printed in titanium. The parts were printed at Airbus’s Reference Manufacturing shop in Filton, with a full set of four fences for one aircraft made in a single 26-hour build. Each printed part replaces the original one-for-one and is supplied with an EASA Form 1, the certificate that releases a part for use on an aircraft. Satair believes it was the first certified metal 3D-printed spare part to fly (Airbus, 2020). At the time, Satair also had more than 300 part numbers certified for 3D printing, including tools and ground support equipment, across all Airbus aircraft families (Airbus, 2020).
Environmental, Social and Economic Impact
Satair reports that, compared with conventional methods, 3D printing the wingtip fence cut total non-recurring costs (the one-off costs of developing and setting up production) by 45% and shortened the lead time. It also made it less likely that the aircraft would be grounded while waiting for the part. According to Satair, the printed part meets the same safety requirements as the conventional part, and four more customers asked for it after the first delivery. Satair also identified further titanium parts that could be produced more economically by 3D printing (Airbus, 2020). More widely, the European Commission reports that the EU-funded REPAIR project, which used 3D printing to repair defective aircraft parts and to produce spare parts on demand, promised benefits including lower maintenance costs, job creation and improved aircraft safety (European Commission, 2017).
Satair says that, when the economics, safety standards and traceability allow, extending the life of parts can reduce the need for new material, make parts more available, lower costs and help airlines return grounded aircraft to service (Satair, 2026b). Across the sector, KPMG reports that certified used serviceable material is typically 20 to 40% cheaper than new parts (KPMG, 2024). EASA reports that aircraft going through the end-of-life process can reach close to zero landfill. It also expects more than 30% of the current European fleet to retire over the next decade (EASA, 2024).
3D printing suits one-off parts and small batches and needs no moulds, which makes it useful for producing spare parts. It also allows parts to be made on demand rather than stockpiled (Schwander, 2024). It can use less metal than machining, the conventional method in which a part is cut from a solid block. In aerospace, machining can use 10 to 20 kg of metal for every 1 kg of finished part, and up to 40 kg for complex parts. 3D printing builds parts close to their final shape, so this ratio can fall close to 1 to 1. Manufacturers are increasingly using 3D printing for titanium parts because it sharply reduces production costs and material waste (Mohd Yusuf, Cutler and Gao, 2019). For a single spare part, the International Civil Aviation Organization (ICAO) reports that 3D printing can cut raw material waste by as much as 95% (ICAO, 2016). However, metal 3D printing currently uses more energy for each part than conventional manufacturing (Mohd Yusuf, Cutler and Gao, 2019). The original wingtip fence was cast rather than machined, and no figure is available for the material used in Satair’s printed part.
Titanium metal is listed as both a strategic and a critical raw material under the EU Critical Raw Materials Act, which sets out a framework for a secure and sustainable supply of these materials (Regulation (EU) 2024/1252). Two-thirds of titanium metal in Europe is used by the aerospace sector, and the EU relies fully on imports of titanium sponge, the raw form of the metal (Georgitzikis, D’Elia and Eynard, 2022).
Replicability
The organisations below use repair, part exchange and on-demand 3D printing to keep transport equipment supplied with spare parts, including parts that are no longer made.
RAMLAB (Netherlands), based in the Port of Rotterdam, builds MaxQ, an automated system to 3D print and repair metal parts. RAMLAB says it serves industries where downtime is expensive and spare parts take long to arrive, including aerospace and marine. In 2017, it worked with four partners to produce the WAAMpeller, which the partners describe as the world’s first class-approved 3D-printed ship’s propeller. The propeller was certified by a ship classification society, built from 298 layers of nickel aluminium bronze, and behaved in the same way as a conventional cast propeller in all tests, including crash-stop tests.
AM4Rail (Austria) is a research project led by Fraunhofer Austria with ÖBB Train Tech, Wiener Linien, Wien Energie and research partners. It uses image-processing and text-mining software to analyse rail companies’ technical drawings, identifies spare parts that could be 3D-printed on demand, and assesses each part economically and environmentally. The project estimates that printing spare parts on demand could cut downtime of the assets studied by 10% and spare-part supply costs by up to 30% (FFG, 2024).
Siemens Mobility (Germany) repairs and overhauls rail components. Through its Unit Exchange service, it sends customers an identical replacement part while their defective part is repaired, and it says repaired parts are up to 50% cheaper than new ones (Siemens Mobility, n.d.). Through its Easy Sparovation Part service, the company also 3D-prints rail spare parts on demand, including obsolete ones. It reports more than 31,000 printed parts sold to more than 110 customers, more than 2,100 parts held in a virtual stock of digital designs, and delivery times cut by up to 90%. A 2024 life cycle assessment by the company found that 3D printing a coupling cover for its Avenio tram cut CO₂ emissions by up to 75% compared with conventional manufacturing.
Deutsche Bahn (Germany) has used 3D printing since 2015, mainly to produce spare parts for maintaining its trains and locomotives. The company reports more than 200,000 printed parts for more than 1,000 applications. It uses 12 printing processes with metal, plastic and sand, and its printed parts range from a 540 kg gearbox housing to tablet holders and coat hooks. Deutsche Bahn says 3D printing helps when manufacturers or suppliers cannot deliver important spare parts or no longer make them. It keeps more than 1,000 designs in a digital warehouse and produces parts as needed, which it says saves storage costs and space and shortens delivery times. The company reports that faster and more efficient access to spare parts has saved it more than €20 million (Deutsche Bahn, 2025).

